first commit

2025-03-06 11:15:32 +01:00
commit 7b30d6e298
5276 changed files with 2108927 additions and 0 deletions
--- a/MySensorGateWay/MySensorGateWay.ino
+++ b/MySensorGateWay/MySensorGateWay.ino
@@ -0,0 +1,85 @@
+  /*
+ * Copyright (C) 2013 Henrik Ekblad <henrik.ekblad@gmail.com>
+ * 
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ * 
+ * DESCRIPTION
+ * The ArduinoGateway prints data received from sensors on the serial link. 
+ * The gateway accepts input on seral which will be sent out on radio network.
+ *
+ * The GW code is designed for Arduino Nano 328p / 16MHz
+ *
+ * Wire connections (OPTIONAL):
+ * - Inclusion button should be connected between digital pin 3 and GND
+ * - RX/TX/ERR leds need to be connected between +5V (anode) and digital ping 6/5/4 with resistor 270-330R in a series
+ *
+ * LEDs (OPTIONAL):
+ * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
+ * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
+ * - ERR (red) - fast blink on error during transmission error or recieve crc error  
+ */
+
+#include <SPI.h>  
+#include <MySensor.h>  
+#include <MyGateway.h>  
+#include <stdarg.h>
+
+#define INCLUSION_MODE_TIME 1 // Number of minutes inclusion mode is enabled
+#define INCLUSION_MODE_PIN 3 // Digital pin used for inclusion mode button
+
+
+MyGateway gw(DEFAULT_CE_PIN, DEFAULT_CS_PIN, INCLUSION_MODE_TIME, INCLUSION_MODE_PIN,  6, 5, 4);
+
+char inputString[MAX_RECEIVE_LENGTH] = "";    // A string to hold incoming commands from serial/ethernet interface
+int inputPos = 0;
+boolean commandComplete = false;  // whether the string is complete
+
+void setup()  
+{ 
+  gw.begin();
+}
+
+void loop()  
+{ 
+  gw.processRadioMessage();   
+  if (commandComplete) {
+    // A command wass issued from serial interface
+    // We will now try to send it to the actuator
+    gw.parseAndSend(inputString);
+    commandComplete = false;  
+    inputPos = 0;
+  }
+}
+
+
+/*
+  SerialEvent occurs whenever a new data comes in the
+ hardware serial RX.  This routine is run between each
+ time loop() runs, so using delay inside loop can delay
+ response.  Multiple bytes of data may be available.
+ */
+void serialEvent() {
+  while (Serial.available()) {
+    // get the new byte:
+    char inChar = (char)Serial.read(); 
+    // if the incoming character is a newline, set a flag
+    // so the main loop can do something about it:
+    if (inputPos<MAX_RECEIVE_LENGTH-1 && !commandComplete) { 
+      if (inChar == '\n') {
+        inputString[inputPos] = 0;
+        commandComplete = true;
+      } else {
+        // add it to the inputString:
+        inputString[inputPos] = inChar;
+        inputPos++;
+      }
+    } else {
+       // Incoming message too long. Throw away 
+        inputPos = 0;
+    }
+  }
+}
+
+