#include #include #include #include "DHT.h" // DHT #define DHTPIN A0 // what pin we're connected to #define DHTTYPE DHT11 // DHT 11 // Initialize DHT sensor for normal 16mhz Arduino DHT dht(DHTPIN, DHTTYPE); // Baromètre // ################# Barometre #### Adafruit_BMP085 bmp; // ##################### float temperature = 0.0; float pressure = 0.0; float pression = 0.0; float presiune = 0.0; float humidite = 0.0; const unsigned long activation = 111269; const unsigned long idTemp=1969; const unsigned long idPressure=2069; const unsigned long idPression=2169; const unsigned long idLum=2269; const unsigned long idHum=2369; const unsigned long desactivation = 962111; const unsigned int delai = 11; // WIFI const char* ssid = "Livebox-37cc"; // Le nom de votre réseau Wifi const char* password = "8A6060920A8A86896F770F2C47"; int ledPin = 2; // GPIO2 WiFiServer server(80); #define DEBUG true void setup() { Serial.begin(115200); delay(10); pinMode(ledPin, OUTPUT); digitalWrite(ledPin, LOW); // Connect to WiFi network Serial.println(); Serial.println(); Serial.print("Connecting to "); Serial.println(ssid); WiFi.begin(ssid, password); while (WiFi.status() != WL_CONNECTED) { delay(500); Serial.print("."); } Serial.println(""); Serial.println("WiFi connected"); // Start the server server.begin(); Serial.println("Server started"); // Print the IP address Serial.print("Use this URL to connect: "); Serial.print("http://"); Serial.print(WiFi.localIP()); Serial.println("/"); Wire.begin(4, 5); } void loop() { // Check if a client has connected WiFiClient client = server.available(); if (!client) { return; } // Wait until the client sends some data Serial.println("new client"); while(!client.available()){ delay(1); } // Read the first line of the request String request = client.readStringUntil('\r'); Serial.println(request); client.flush(); // Match the request int value = LOW; if (request.indexOf("/LED=ON") != -1) { digitalWrite(ledPin, HIGH); value = HIGH; } if (request.indexOf("/LED=OFF") != -1) { digitalWrite(ledPin, LOW); value = LOW; } // Set ledPin according to the request //digitalWrite(ledPin, value); // Return the response client.println("HTTP/1.1 200 OK"); client.println("Content-Type: text/html"); client.println(""); // do not forget this one client.println(""); client.println(""); client.print("Led pin is now: "); if(value == HIGH) { client.print("On"); } else { client.print("Off"); } ///////////////////////////// // //////////////////////////// digitalWrite(13, HIGH); // turn the LED on (HIGH is the voltage level) delay(10); // wait for a second digitalWrite(13, LOW); barometre(); doDHT(); #ifdef DEBUG Serial.print("Send"); #endif myMessageSend(idTemp,temperature * 100); myMessageSend(idPressure,pressure * 10); myMessageSend(idHum,humidite); myMessageSend(idPression,pression * 10); // LUX // R=K*L^-gamma // R étant la résistance pour un niveau d'éclairement L. int lum = analogRead(1); int lux = (1000.0 * lum / 1024.0); myMessageSend(idLum,lux); client.println(""); client.println(""); client.println(""); client.print(""); client.print(""); client.print(""); client.print(""); client.print(""); client.println("
Click here turn the LED on pin 2 ON
Click here turn the LED on pin 2 OFF
Temperature=");client.print(temperature);client.print("
Pressure =");client.print(pressure);client.print("
Humidite =");client.print(humidite);client.print("
Pression =");client.print(pression);client.print("
Luminosite =");client.print(lux);client.print("
"); delay(1); Serial.println("Client disonnected"); Serial.println(""); } // Commande pour barometre humidité température // Virtual Device // http://192.168.0.10:8080/json.htm?type=command¶m=udevice&idx=160&nvalue=0&svalue=23.3;50;2;1024.20;1024&battery=89 void doDHT() { // Reading temperature or humidity takes about 250 milliseconds! // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor) float h = dht.readHumidity(); humidite = h; // Read temperature as Celsius float t = dht.readTemperature(); // Read temperature as Fahrenheit float f = dht.readTemperature(true); // Check if any reads failed and exit early (to try again). if (isnan(h) || isnan(t) || isnan(f)) { // Serial.println("Failed to read from DHT sensor!"); return; } else { // Compute heat index // Must send in temp in Fahrenheit! float hi = dht.computeHeatIndex(f, h); #ifdef DEBUG Serial.print("Humidity: "); Serial.print(h); Serial.print(" %\t"); Serial.print("Temperature: "); Serial.print(t); Serial.print(" *C "); Serial.print(f); Serial.print(" *F\t"); Serial.print("Heat index: "); Serial.print(hi); Serial.println(" *F"); #endif } } void barometre() { /* See Example: TypeA_WithDIPSwitches */ // mySwitch.switchOn("00001", "10000"); // delay(1000); // BMP if (bmp.begin()) { temperature = bmp.readTemperature(); pressure= bmp.readPressure() / 100.0; pression = pressure / 101.325; pression = pression * 0.760 * 100; // http://en.wikipedia.org/wiki/Atmospheric_pressure#Mean_sea_level_pressure // Serial.print("Presiure la nivelul marii (calculata) = "); presiune = bmp.readSealevelPressure(19) / 101.325; presiune = presiune * 0.760; #ifdef DEBUG Serial.print("Temperature="); Serial.println(temperature); Serial.print("pressure="); Serial.println(pressure); Serial.print("pression="); Serial.println(pression); #endif } } void myMessageSend(long id, long value) { #ifdef DEBUG Serial.print("Send id="); Serial.print(id); Serial.print(" value="); Serial.println(value); #endif //delay(5000); //delayMicroseconds(TWOTIME*8); } //-------------------------------------------------------------------------------------------------- // Read current supply voltage //-------------------------------------------------------------------------------------------------- // long readVcc() { // bitClear(PRR, PRADC); ADCSRA |= bit(ADEN); // Enable the ADC // long result; // // Read 1.1V reference against Vcc // #if defined (__AVR_ATtiny24__) || defined(__AVR_ATtiny44__) || defined(__AVR_ATtiny84__) // ADMUX = _BV(MUX5) | _BV(MUX0); // For ATtiny84 // #elif defined (__AVR_ATtiny25__) || defined(__AVR_ATtiny45__) || defined(__AVR_ATtiny85__) // ADMUX = _BV(MUX3) | _BV(MUX2); // #else // ADMUX = _BV(REFS0) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1); // For ATmega328 // #endif // // ADCSRB = 0; // // delay(2); // Wait for Vref to settle // ADCSRA |= _BV(ADSC); // Convert // while (bit_is_set(ADCSRA,ADSC)); // result = ADCL; // result |= ADCH<<8; // result = 1126400L / result; // Back-calculate Vcc in mV // // ADCSRA &= ~ bit(ADEN); bitSet(PRR, PRADC); // Disable the ADC to save power // // // analogReference(DEFAULT); // // return result; // Vcc in millivolts //}