extern "C" {
#include "user_interface.h"
}

#include <Wire.h>
#include <ESP8266WiFi.h>


const char* ssid     = "Livebox-37cc";
const char* password = "8A6060920A8A86896F770F2C47";
//const char* ssid = "SFR_E4C8"; // Put your SSID here
//const char* password = "Sept/6-Six/4"; // Put your PASSWORD here

const int sleepTime  = 120; //Power down WiFi for n seconds


// int status = WL_IDLE_STATUS;     // the Wifi radio's status
WiFiClient client;


// domoticz
const char * domoticz_server = "192.168.1.3"; //Domoticz port
int port       = 81; //Domoticz port
int idx        = 158; //IDX for this virtual sensor, found in Setup -> Devices
float lum     = 0;


int inByte;
String sChaine = "";
void setup()
{
  Serial.begin(9600);
  initWifi();

}

void loop() {
  if (Serial.available()) {
    delay(100);
    while (Serial.available()) {
      inByte = Serial.read();
      if ( inByte > 32 && inByte < 123)
      {
        sChaine += char(inByte);
      }
    }
    sChaine.trim();
    Serial.println(sChaine);
    if (sChaine != "") {
      printInfo();
    }
    sChaine = "";
    delay(100);
  }
}
//
//void readLum()
//{
//  lum = analogRead(2);
//  Serial.println(lum);
//}
//void sleepWifi()
//{
//  //Time to let the WiFi go to sleep!
//  Serial.println("Sleeping...");
//  WiFi.disconnect();
//  WiFi.mode(WIFI_OFF);
//  WiFi.forceSleepBegin(sleepTime * 1000000L); //In uS. Must be same length as your delay
//  delay(sleepTime * 1000); //Hang out at 15mA for 6 seconds
//  WiFi.mode(WIFI_STA);
//  Serial.println("Awake!");
//}
void initWifi()
{
  WiFi.mode(WIFI_AP);
  WiFi.begin(ssid, password); //Connect to local Wifi

  Serial.println();
  Serial.print("Connecting to WiFi");
  while (WiFi.status() != WL_CONNECTED)
  {
    Serial.print(".");
    delay(500);
  }
  Serial.println("WiFi Connected");
    Serial.println("");
  Serial.println(WiFi.localIP());
}

void printInfo()
{
  // Domoticz format /json.htm?type=command&param=udevice&idx=IDX&nvalue=0&svalue=TEMP;HUM;HUM_STAT

  if (client.connect(domoticz_server, port)) {

    client.print("GET " + sChaine); ///json.htm?type=command&param=udevice&idx=");
//    client.print(idx);
//    client.print("&nvalue=0&svalue=");
//    client.print((1000.0 * lum / 1024.0));
//    client.print(";0"); //Value for HUM_STAT. Can be one of: 0=Normal, 1=Comfortable, 2=Dry, 3=Wet
    client.println(" HTTP/1.1");
    client.print("Host: ");
    client.print(domoticz_server);
    client.print(":");
    client.println(port);
    client.println("User-Agent: Arduino-ethernet");
    client.println("Connection: close");
    client.println();

    client.stop();
  }
}